Working Environment
Weather
Access and Egress
Duration and frequency of use
Fragile roofs
Consequences of a potential fall
Maintenance
Inspections
Emergency rescue
Installation and removal
What is collective protection
What is personal protection
Why give priority to collective measures
Last resort
Competence

Introduction

The number one construction killer in any country is falling from heights, and this is principally due to the lack of proper edge protection in a variety of construction tasks. This work accounts for more than half of all deaths in the industry every year, and a significant amount of all major and over 3 day lost time injuries.

The most frequent problem is inadequate scaffolding, with no proper access or no guard rails to prevent falls. Scaffolding is often erected by unqualified operatives, and is sometimes improvised, using unsuitable materials. Apart from scaffolding problems, other causes of falls include unprotected openings in buildings, lack of edge protection in roof work, lack of crawling boards on fragile roofs, demolition work and inappropriate use of ladders and hoists.

The poor selection, use and maintenance of equipment causes falls, for example, using a ladder because it’s easier than erecting a tower scaffold. Ladders should only be used for low risk, short duration work, e.g. work which takes minutes not hours to complete.

Research in the UK shows that 60% of all major injuries are caused by falls from height of below 2 metres, commonly from a ladder. Traditionally, significant risk concerning working at height has begun with work over 2 metres. The figure above regarding major injuries proves this to be a mistake.

All work at height where there is a significant risk of a fall liable to cause personal injury should be risk assessed and appropriate controls implemented. This assessment might be made by the employer, the self-employed, and/or any person that oversees the work of others to the extent of their control (for example facilities managers or building owners who may contract others to work at height). In order to minimise the risk from such work, a risk assessment must be conducted in advance in order to decide what realistic fall protection is available. Remember risk is a combination of two factors – likelihood and severity; how likely is the person to fall and how bad will the consequence of the fall be?

As well as the risks posed by the work at height itself, consider those caused by falling objects and by accessing the work location. For example, climbing on and off a roof or using ladders can pose significant risks.

 

Those responsible should ensure that:

• all work at height is properly planned and organised;
• those involved in work at height are competent;
• the risks from work at height are assessed and appropriate work equipment is selected and used;
• the risks from fragile surfaces are properly controlled; and
• equipment for work at height is properly inspected and maintained.

 

The risk assessments should apply to all existing places of work and means of access for work at height, collective fall prevention (e.g. guardrails and working platforms), collective fall arrest (e.g. nets, airbags etc), personal fall protection (e.g. work restraints, fall arrest and are designed to reduce this risk and the number of related injuries each year.

 

There is now a Hierarchy of Working at Height, with emphasis placed on elimination of the need to work at height in the first instance. Where this is not realistic (reasonably practicable) then consideration must be given to the use of;

• collective fall prevention (e.g. guardrails and working platforms),
• collective fall arrest (e.g. nets, airbags etc),
• personal fall protection (e.g. work restraints, fall arrest and rope access such as boatswains chair)
• and as a last resort ladders, step ups, trestles, stilts etc.

 

The working at height risk assessment must consider the following issues;

 

Working Environment

This would include issues such as sloping, uneven or soft ground conditions; obstructions such as steelwork, pipework or overhangs; any fragile surfaces and maximum floor loadings.

 

Weather

All work at height risk assessments must consider the possibility of adverse weather and its impact on the health and safety of the worker. Rain, snow and ice increase the risk of slips on a roof. High winds can mean that handling large objects such as roofing sheets is unsafe since the person and/or roof sheet can be blown off the roof. High winds can also vibrate loose couplings on scaffolds. Low temperatures can also make some roofing materials especially brittle, so increasing the risk of falling through fragile roof materials, such as plastic roof lights. Rain, snow and high winds all carry an increased health risk to the worker form localised cooling of the extremities (frostbite) and general cooling of the body core (hypothermia) which can be dangerous. Sandstorms can be a consideration since they can severely limit visibility, so a crane operator may not be able to see the worker who is operating from a suspended basket on the end of the crane. Lightning can be another consideration during work at height activities such as steel erection. You must ensure that any work at height is postponed if weather conditions present a danger to the health and safety of worker

 

Access and Egress

How will the workers get up to and down from the work at height? Portable ladders are not the most preferred option since they do not prevent falls or limit the consequences of the fall. Furthermore they also require 3 points of contact which is not always possible when loads are being carried. It is preferred, where possible, to provide temporary stairs or scaffold access towers with internal stairs, rather than portable ladders.

 

Duration and frequency of use

Longer duration or regular jobs generally justify a better standard of fall protection, e.g. a tower scaffold, podium step or cherry picker rather than a ladder or stepladder. A ladder or stepladder may be acceptable for short duration work, e.g. replacing a light bulb whereas building a tower or podium would not be reasonable because the task itself takes only a few seconds to do. But, installing several rows of light bulbs or fluorescent strips in a false ceiling refurbishment may justify the use of a tower or podium steps because the task takes longer, so the likelihood of a fall increases.

 

Fragile roofs

Roofing materials such as asbestos cement, plastic or glass are unlikely to bear the weight of a person. Asbestos sheets deteriorate over time leaving the remaining material in a particularly fragile state. Similarly plastic roof lights deteriorate due to the effects of ultra violet light from the sun leaving it brittle. Some materials are designed not to be load bearing and where this is the case they must be accompanied with an appropriate warning sign.

 

Where a person must work on fragile roofs we must ensure wherever possible that suitable platforms, coverings, guardrails and the like are provided (and used) to minimise the risk. Where a risk of a person at work falling remains, do all that is ‘reasonably practicable’ to ensure suitable and sufficient measures are implemented to minimise the consequences of a fall.

 

Consequences of a potential fall

If you have to use a fall arrest system you must make sure there is adequate clearance for it to deploy, so the user does not hit an obstruction or the ground before the fall is stopped. If you have to use nets or airbags they should be located as close as possible to the working level because they do not work as effectively if the fall distance is too great. Nets assume that there are suitable strong points to attach the safety net to.  Air bags prohibit all work at ground floor level within that area.

 

Maintenance

Basic care for fall protection safety equipment will prolong the life of the equipment and contribute toward the performance of its vital safety function. Proper storage and maintenance after use is as important as cleaning the equipment of dirt, corrosives or contaminants. The storage area should be clean, dry and free of exposure to fumes or corrosive elements.

 

Inspections

All work equipment and personal protective equipment should be regularly inspected by a competent person. There is a wide range of possible causes of degradation of materials used for work at height (including abuse, general wear and tear, edge/surface damage, weather, dirt, grit, chemicals, dropping, subjection to excessive loading, falls).Where fall restraint/fall arrest equipment is concerned the textiles deteriorate slowly with age regardless of use. However, the most common cause of strength loss in textile equipment is through abrasion (either by grit working into the strands or by chafing against sharp or rough edges) or by other damage such as cuts. All of these defects are observable by inspection.

 

Equipment should be subject to different levels of inspection at different times through its use:

• pre-use checks;

• detailed inspections

 

Emergency rescue

Where a worker has fallen from height but has been wearing a fall arrest system, such as a harness, it is vital that a rescue can be carried out quickly where the worker is now suspended.  This is very important due to the phenomena of ‘suspension trauma’ which is one of the effects of being suspended in a harness with the tightening of the leg straps that bear the body weight of the suspended person. Gravity pulls the blood down into the legs (venous pooling). This pooling of blood in the legs reduces the amount of blood flowing in the body and so the heart rate increases and breathing increases to maintain the flow of oxygenated blood to the brain and organs. When this fails the heart rate slows and the casualty faints. This reduced heart rate can critically reduce both the quality and quantity of oxygenated blood to the brain and other vital organs with serious consequences of kidney failure or brain damage. Therefore it is important that rescue procedure is developed and practiced. It is not acceptable just to rely on the emergency services. Emergency procedures need to be considered for ALL reasonably foreseeable circumstances. The measures need to be covered in the risk assessment and planned prior to the work activity being carried out. The key is to get the person down safely in the shortest possible time and before the emergency service response

 

Installation and removal

When selecting work equipment look at all the risks, not just those associated with the ‘use’ phase. It may take two or more people to assemble a mobile tower scaffold to get onto a roof and install temporary edge protection, whereas the repair may need only one person on the roof, putting several people at risk so one person can work safely. A better solution would be to use a cherry picker (mobile elevated working platform), so one person can perform the task safely from the working platform. This avoids others being put at risk during set up and dismantling. Where the risk assessment identifies a significant likelihood of violent, unexpected movement, such as a vehicle colliding with the MEWP on a road, then the use of a restraint harness and line would also be considered in order to prevent the user being thrown out of the working platform.

 

There are even more risks associated with work on a fragile fibre/asbestos cement roof. Where possible, use a cherry picker or tower scaffold to access and repair a leaking skylight. This will remove risks associated with setting up and dismantling work equipment on the roof.

 

What is collective protection?

Collective protection is equipment which can protect more than one person and, once properly installed or erected, does not require any action by them to make sure it will work. These protect all workers without the need for restrictive working lines, harnesses etc. Examples which prevent a fall include, scaffolds, tower scaffolds and cherry pickers which have guard rails and equipment which minimises the consequences of a fall, which would include nets and airbags.

 

What is personal protection?

Personal protection is equipment which protects only the user/wearer and requires action by the individual, such as properly wearing and adjusting it, for it to work. Examples include work restraint equipment which prevents a fall and fall arrest equipment such as inertia reel equipment which minimises the consequences of a fall as well as rope access systems such as a boatswain’s chair.

 

Why give priority to collective measures?

Collective measures have several advantages. They are easier to use, protect everyone at risk in the work area and need less effort in terms of maintenance and user training. Personal measures have disadvantages – they require a high level of training and maintenance and they only protect the user. It has long been known that workers are unreliable and even when issued suitable worker restraint/ fall arrest equipment can fail to use it correctly e.g. not clip onto the strong point.

 

Additionally even falling just a short distance can generate extremely high loads on the user’s body, with point pressures exceeding 1,500kg. Without a shock absorber built into the fall arrest system these forces are likely to severely injure the worker and can even result in a fatality.

 

So our priority is to provide collective fall prevention (a safe place of work) where the likelihood of falling people and or objects are minimised. Examples would include;

• Scaffolding: A correctly designed and built scaffold should be as safe to work on as standing on the ground.
• Mobile elevating work platform (MEWP): As with a scaffold, a correctly positioned and used MEWP should be as safe as working with our feet on the ground.
• Suspended access platform: When correctly installed and operated, these too should be as safe as standing on the ground.

 

Last resort

Where the work is fast moving, short duration or difficult access it is sometimes only realistic to use a ladder or ‘hop up’ but only if the work is low risk and of short duration and does not require both hands at any time to complete the activity.

• Hop ups are a suitable and relatively safe, method of gaining ‘centimetres’ in height not metres.

• Ladders are really to be seen as a last resort as a means of access and then only when used correctly by competent persons.

 

Competence

Competence concerns an individual’s mental and physical suitability for a task. This is important because if someone has a fear of heights no amount of training will make then competent for working at height. So all of the above will only work if ALL workers are competent and suitably supervised against the assessed risks and in the safe systems of work. Information and instruction shall be provided on the nature of the hazards and control measures arising from the risk assessment. Levels of supervision shall be determined based on the risk assessment and other factors linked to the activity including type of work, equipment used, duration etc.  Regular refresher training should be considered in order to prevent ‘skill fade’.

Some personal factors that might mean that a person might not be considered suitable for work at height would include:

• Recurring dizziness

• Epilepsy

• Psychiatric conditions (inc fear of heights)

• Heart condition

• Severe lung conditions

• Alcohol and drug abuse

• Significant impaired joint function

• Medication that recommends you do not operate machinery could also be a problem